ITC, S.A. (Ingenieria y Tecnicas Clinica s, S.A.) of Arganda del Rey (Madrid) at MEDICA 2021 in Düsseldorf -- MEDICA - World Forum for Medicine
Manage stand orders
Select Option

ITC, S.A. (Ingenieria y Tecnicas Clinica s, S.A.)

C/ Tungsteno, 11-15 (poligono Industrial El Olivar), 28500 Arganda del Rey (Madrid)
Spain
Telephone +34 91 8719950
Fax +34 91 8706601
impexp@itcsal.com

Submit your contact details

Provide your contact details to the exhibitor. Optionally, you may also add a personal message.

Please log in

You must be logged in to send the contact request.

An error has occurred

Please check your internet connection or try again later.

Message has been sent

Your message to the exhibitor was sent successfully.

Hall map

MEDICA 2021 hall map (Hall 11): stand E21

Fairground map

MEDICA 2021 fairground map: Hall 11

Contact

Jesus Muñoz

CEO
General Management

Tungsteno Str. 11-15 Industrial Area El Olivar 28500 Arganda del Rey (Madrid)
28500 Madrid (Arganda del Rey), Spain

Phone
+34 91 871 99 50

Email
itcsal@itcsal.com

Manuel Ortiz

International Account Manager
Export Department

Tungsteno Str. 11-15 Industrial Area El Olivar 28500 Arganda del Rey (Madrid)
28500 Madrid (Arganda del Rey), Spain

Phone
+34 91 871 99 50

Email
impexp@itcsal.com

Miguel Gil

International Product Manager
Bed Head Units

Tungsteno Str. 11-15 Industrial Area El Olivar 28500 Arganda del Rey (Madrid)
28500 Madrid (Arganda del Rey), Spain

Phone
+34 91 871 99 50

Email
itcsal@itcsal.com

Please log in

You must be logged in to use matchmaking

Please log in for matchmaking

Registration is required to use the networking service and a separate registration for matchmaking. Please register for Matchmaking first.

Let's get started!

Welcome to Matchmaking. Would you like to get in touch with ?

Our range of products

Product categories

  • 01  Imaging and diagnostics / medical equipment and devices
  • 01.09  Hospital equipment, care equipment
  • 01.09.14  Installation and equipment of supply conduits (gas, compressed air, oxygen, water, electricity, …)

Our products

Product category: Installation and equipment of supply conduits (gas, compressed air, oxygen, water, electricity, …)

NOXtec 1000 Nitric Oxide monitor and dosifier

NOXtec 1000 is a medical device which both doses and monitors the supply of nitric oxide (NO).

NO is a gaseous vasodilator used to treat pulmonary arterial hypertension. It is supplied to the patients mixed with medical oxygen. NOXtec 1000 supplies a stable dose throughout the therapy, even triggering an automatic exchange of the cylinders (it can harbor two cylinders) if needed.

NOXtec automatically calculates the necessary dosing flow, thanks to a breathing flow sensor applied to the patients circuit. Alternatively, the dosing flow can be set manually.

Thanks to the continuous sampling of the NO-O2 mixture flow supplied, NOXtec is able to monitorize the NO concentration that the patient is receiving, and to check if this value is placed within predetermined thresholds.

NOXtec 1000 also monitors trace quantities of nitrous oxide (NO2) in the mixture, a highly toxic gas which can compromise the patients safety during the treatment. NOXtec 1000 triggers an alarm when this trace surpasses a threshold value.

More Less

Product category: Installation and equipment of supply conduits (gas, compressed air, oxygen, water, electricity, …)

Regulators (JUST PRESS), Flowmeters (JUST FLOW) & Vacuum regulatos (JUST VAC)

JUST PRESS Gas regulators specially designed for its use on home oxygen therapy services or in hospitals without oxygen piped network. Our models incorporates a manometer to read pressures of the cylinder and a side gas outlet of one of the different standards available. We have available models with ball or dial flowmeter, and with differents scales. They can be supplied with a regulated output using flexible hose.

JUST FLOW Ball flowmeter appropiate for use in hospitals. 360º adjustable scale for easy reading, with diferent scales. Appropiate for use in hospitals with a gas network.

JUST FLOW dial flowmeter type, turning the top control button with “click” position, the selected flow appears in the front window.
We have Models with
• Direct output to humidifier jar
• Output with flow selection, which diverts the flow through a humidifier jar or a front spigot for flexible hose, if necessary
Can be provided individually or on a dual version, and it can be mounted either with a direct connector, a clamp to a rail or a Ø38,0 mm bar flange.

JUST VAC Vaccum regulators available in plastic, metalic and venturi effec types.Produces aspiration by Venturi-effect connected to an Oxygen or Medicinal Air outlet.
Has a valve to regulate the suction. Can be mounted either with a direct connector, a clamp to rail or a bar flange.

More Less

Product category: Installation and equipment of supply conduits (gas, compressed air, oxygen, water, electricity, …)

JUST PLUG

Sockets & Outlets for bedheads and ambulances, either with a surface box or recessed wall. Common base blocks to all standards, with check valve and the possibility to adjust the feeding angle, available with Ø10.0 mm copper tube for welding and fl exible hose outlet. Possibility of mounting the outlet in a vertical or horizontal position without removing the base block.

Available for oxygen, vacuum, medical air and nitrous oxide (Consult our staff about other gases). Manufactured according to European and American standards.

More Less

Product category: Installation and equipment of supply conduits (gas, compressed air, oxygen, water, electricity, …)

Bedhead units and accessories

They can be configured to suit the hospital center for hosptalization area and also for the intensive care one.  All additional accessories can also be added to the equipment at the customer's request, for example plugs, gas separators, nurses' bells, switches, ect.

HOSPITALIZATION HEADBOARDS BASIC is a wall system capable of integrating the supply of medical gases, electricity, telephony and computer communications. There is the possibility of individual, double and triple assembly, in order to make the electrical and gas pipes independent. Our technical office will adapt the dimensions, colors and final equipment to the specific needs of each project on request.

HOSPITALIZATION HEADBOARDS CLASSIC is a wall headboard capable of integrating the supply of medical gases, electricity, telephony, computer communications and the nursing call, as well as providing indirect and reading light to a patient's bed

The CLAIRE Hospital Headboard is a headboard designed to meet the highest aesthetic and functional requirements, becoming one more architectural element of the environment. The mechanisms, except for the gas intakes, are incorporated in its lower profile, parallel to the ground, being hidden by the front cover.

The CLAIRE Vertical Hospital Headboard is a headboard designed to meet the highest aesthetic and functional requirements, becoming one more architectural element of the environment. Capable of integrating the supply of medical gases, electricity, telephony, computer communications and the nursing call, as well as providing indirect light to a patient's bed.

NEXUS LT suspended ceiling columns have been designed to integrate the supply of medical gases, electrical and communications, and are especially indicated for use in surgical, critical areas and in neonatology units. • The column consists of a ceiling support and a horizontal profile that contains six isolated compartments (three in the LT-S version) with the capacity to install the equipment necessary for each project. • Its design makes it possible to have gas intakes.

The NEXUS II LM and LX suspended ceiling headboards have been designed to integrate the supply of medical gases, electrical and communications, and are especially suitable for use in emergency, resuscitation and intensive care areas. The NEXUS II LM headboard has two ceiling supports (three for the LX version) and the horizontal profile contains four isolated compartments with the capacity to install the necessary equipment for each project. • They are complemented with rotating trolleys of different heights.

The suspended trolley is able to rotate smoothly on a vertical axis, and additionally move horizontally, supporting equipment and accessories at the patient's bedside, without the need for supports on the floor or on the walls. There are two standard widths and two lengths adaptable to every need and both trolleys have two lower profiles for anchoring various accessories from our rail line.

Other accesories like separation curtain specially designed to preserve the intimacy between patients, being possible to monitor them by another person who remains standing. The support is deployed by pulling the knob at the end and is retracted by pushing in the opposite direction, and it is also possible to adapt it parallel to the wall to take advantage of the space when its use is not necessary. We have versions for rail, for wall and for Ø38.0 mm tube. Made of Anodized Aluminum, Chromed Brass and Stainless Steel. 

MONITOR SUPPORTS has a specific design to support bedside monitors, allowing their orientation on a vertical axis and their horizontal inclination, to facilitate viewing from any point. The rail version is adapted by means of a clamp with two knobs, the wall version also admits height adjustment by means of a vertical sliding profile and the 038 bar version has two flanges for fixing. It incorporates a practical wire basket.

More Less

Company news

Date

Topic

04 Nov 2021

ITC's reach in the pandemic crisis.

After more than a year and a half since the beginning of the pandemic, and the confinements, the spanish healthcare business sector has been able to adapt quickly to the situations that arose.

First was the import and production of protection and disinfection systems to combat the coronavirus. Subsequently, and depending on the circumstances in the ICU, companies such as ITC were part of this great technological and logistical challenge given the increase in demand for products related to high-flow respiratory therapies caused by high national hospital pressure.

Being thus capable of overcoming the challenge of adaptation in our country, especially in the peaks of the sanitary crisis, it has also managed to considerably increase its international expansion, supplying, for example, more than twice as many regulators and flowmeters than in previous years to cover the high demand generated by these products, especially the Just Flow C and Just Flow F.

These are essential lines for COVID patients who need to receive oxygen therapy treatments in hospitals with a piped gas network. Only this line of Just Flow products has been able to supply 300% more compared to the previous year, which has also meant an important advance in its export challenge. ITC is present in Asia, Europe, Africa and America, currently obtaining around more than double the sales than in the same period of the previous year.

These are just some examples of the products supplied, but beyond that, other product categories such as the Just Vac vacuum regulator equipment has also been one of the most demanded with an increase in its manufacturing of 169% compared to the same period from the previous year. Other lines such as NOXtec nitric oxide monitoring, or the recent line of Just Plug products (connectors and sockets) continue to generate demand and interest after participating in the last Arab Heath 2021 exhibition, this being the first commercial activity after the pandemic.

A year and a half after the start of this health crisis and until mid-September 2021 there have been a total of 226 million cases of this disease worldwide, to which ITC, thanks to its experience in the health sector, continues to provide significant help to mitigate its effects.

More Less

About us

Company portrait

Ingeniería y Técnicas Clínicas (ITC) was founded in Madrid in 1989. The company was born with a clear vocation for the design and manufacture of medical devices.

Throughout all these years, ITC has been focused on a sole objective: to answer the needs of our clients, taking their problems and necesities as ours. We are aware that the only way to achieve success is to win our clients trust by sharing the same goals.

Our devices are designed and manufactured in compliance with the highest quality standards.

Our commitment to quality and excellence is vital to ensure the trust of those who work with us: clients, providers and institutions. This trust is the core of our competitive force.

Company data

Export content max. 25%
Number of employees 20-49
Foundation 1989
Area of business
  • Imaging and diagnostics / medical equipment and devices
  • Laboratory equipment

Company information as a PDF file