CETA Testsysteme GmbH of Hilden at COMPAMED 2019 in Düsseldorf -- MEDICA - World Forum for Medicine

CETA Testsysteme GmbH

Marie-Curie-Str. 35-37, 40721 Hilden
Telephone +49 2103 2471-0
Fax +49 2103 2471-76

This company is co-exhibitor of
Gaedigk Feinmechanik & Systemtechnik GmbH

Hall map

COMPAMED 2019 hall map (Hall 8a): stand L25

Fairground map

COMPAMED 2019 fairground map: Hall 8a


Dr. Joachim Lapsien

Sales / Marketing

+49 2103 2471-19


Our range of products

Product categories

  • 04  Manufacturing equipment
  • 04.11  Quality assurance
  • 04.11.03  Measuring technolgy, testing technology

Our products

Product category: Measuring technolgy, testing technology

Leak tester CETATEST 825 - New!

The CETATEST 825 is the fourth generation of CETA differential pressure testers.

The differential pressure leak test is based on the comparison of the pressures in the test part volume with the pressure in a tight reference volume. It can be used for fully automatic leak test processes within the cycle time of the production line.

The integrated 7-inch touch-screen with an intuitive operable graphical user interface makes it possible to display a wide range of information (for example, measurement curves, histograms). Operation is possible both via the touch-screen and via a dual-jog dial. Separate start / stop buttons ensure operating safety even in harsh industrial environments.

The memory stores more than 1 million measurement results and 256 test programs.

The product is available from Q4 / 2019.

More Less

Product category: Measuring technolgy, testing technology

Mass Flow Tester CETATEST 615

The CETATEST 615 is a fully automated mass flow tester for the detection of small leaks in large volume test parts. The measurement method is based on the principle of the thermal mass flow measurement.

By using a previously pressurised reservoir volume leakages can be measured without the disturbing effects of a pressure regulation. Temperature effects are automatically compensated. The mass flow caused by the leakage is displayed directly for standard conditions, which can be parameterised.

More Less

Product category: Measuring technolgy, testing technology

Flow Tester CETATEST 915

The flow tester CETATEST 915 is used to measure the flow using compressed air. The device contains a measurement system consisting of a laminar flow element (LFE) and a differential pressure sensor. In the direct test method the air, provided by the internal pressure regulator, flows through the measuring section before it enters the test part. In the indirect test method the measuring section is located behind the test part. Due to the special design of the measuring section a laminar flow is generated. The resulting pressure difference is directly proportional to the volume flow.

More Less

Product category: Measuring technolgy, testing technology


The CETATEST XS is a compact, cost-effective and full automatically working leak tester for the detection of untight parts within the cycle time of the production process. The leak tester uses a gauge pressure sensor for the measurement of the pressure loss caused by the leakage in the test part.

More Less

Company news




Aug 7, 2019

The suitable tester for every testing task - CETA offers a wide range of leak and flow testers

CETA Testsysteme GmbH as a manufacturer of leak and flow testing devices has more than 30 years of experience in industrial testing technology. Compressed air and hydrogen are used as test media. Several thousand CETA test devices are used in production lines by well-known industrial customers all over the world.

In series production a wide variety of products are tested for tightness, e.g. microswitches with a volume of 0.1 ml up to tanks of 1,000 litres. Depending on the application CETA leak testers with gauge pressure or differential pressure sensors are used. Available pressure ranges are between -1 and 30 bar up to 400 bar with the pressure rise method (e.g. testing of injection valves). Products whose flow rate is tested include membranes, filters and cooling ducts. With CETA flow testers a range from 3 ml/min to 200 l/min can be mapped by different laminar flow elements. The tightness of large-volume test parts can be tested by tightness testers with calorimetric mass flow sensor (available measuring ranges 10 to 600 ml/min). Very low leak rates up to 10-6 mbar*l/s can be detected with hydrogen leak testers. The usual industrial interfaces are available for the test devices.

The decision as to which test method is suitable depends, among other things, on whether the test part is directly fillable (e.g. container) or encapsulated (e.g. watches). In addition the production cycle, the specifications for measuring equipment capability and also the temperature of the test part during the test must be observed.

Finding the suitable instrument for a defined testing task requires specific specialist knowledges. Due to its many years of experience in the implementation of testing tasks, combined with its own product development, CETA provides customers with comprehensive support in finding the optimum solution. These added values distinguish CETA as a solution partner for industrial testing tasks.

More Less

About us

Company details

CETA Testsysteme GmbH

CETA is a manufacturer of physical test devices („Made in Germany“) for industrial leak testing and flow measurements in the production line.
Due to different test device technologies and a wide scope of pressure and measurement ranges nearly every test requirement can be fulfilled.
Customers from the automotive industry, medical technology, heating and air conditioning industries, fittings and household appliances industry and packaging industry use CETA test devices for quality control and production assurance.
CETA is certified according to DIN ISO 9001. Since 2004 the calibration laboratory has been accredited according to DIN EN ISO/IEC 17025 as a DKD calibration laboratory respectively as a DAkkS calibration laboratory for the measurand pressure (D-K-19566-01-00).
With more than 30 years of experience, longstanding excellent creditworthiness, international representations as well as several thousands of test devices worldwide, CETA Testsysteme GmbH presents itself as a competent solution partner for industrial leak testing and flow measurement.

More Less

Company information as a PDF file