LUPE Industria Tecnologica de Equipamentos para Laboratorio Ltda. of São Carlos at MEDICA 2017 in Düsseldorf -- MEDICA Trade Fair

LUPE Industria Tecnologica de Equipamentos para Laboratorio Ltda.

Av. Romualdo Villani, 728, 13563651 São Carlos

Telephone +55 16 33611125
Fax +55 16 33720357

This company is co-exhibitor of
ABIMO Brazilian Medical Devices Manufacturers Association

Hall map

MEDICA 2017 hall map (Hall 17): stand A41

Fairground map

MEDICA 2017 fairground map: Hall 17

Our range of products

Our products

Product category: Microtomes

Histologic Bath BH2015

Distension of the cuts and transfer to the blades
The sections from the paraffin blocks form a tape, which must be sectioned into smaller pieces. These sections are then transferred to a Histologic bath containing water at a temperature of 40°C which are maintained for distention. Then immerses the blade diagonally in bath until Histologic sections are attached to it. To avoid blistering the transfer must be careful. Finally, the blade is removed from the water and complete drying and bonding of cuts occur at room temperature or a heated plate.

Equipment built with high strength pu resin, external finishing in white with epoxy paint.

Aluminum inner tank in black with electrostatic powder paint which provides an excellent view of the histological sections and high resistance to oxidation.

Wide borders, with xx mm length, provide accommodation and pre-heating of blades.

On/off key with led indicator through.

Temperature control: room temperature up to 90 degrees with a variation of + / - 2 degrees through digital thermostat.
The design pragmatic functions meets the use requirements analyzed in special laboratories.

Aesthetic functions in synergy with the best laboratorial facilities, results of research in loco.

Thermal protector for disarming high temperature to reach 100°c. General shutdown of the equipment. Automatic reset when the temperature drops 95°c.


Controle de temperatura:
Temperatura ambiente até 90ºc com variação de +/- 2 c, através de termostato analógico ou digital.

Capacity: up to 2 liters of water

Tank height: 90 mm
External dimension: 360 mm
Internal dimension: 260 mm
Equipment height: 100 mm
Weight: 2,5 kg

Power: 350 watts
Voltage: 110/127 volts or 200/240 volts 50/60 hertz

Informações adicionais:
01 instruction manual
01 warranty certificate

More Less

Product category: Microtomes

Embedding System CI 2014

The inclusion is based on placing with the aid of a preheated clamp the tissues that were previously infiltrated in paraffin in a basemold which already contains liquid paraffin on the surface to be split (to be cut in the microtome) downward.
The fragments should be placed in heated paraffin while avoiding the formation of air bubbles around them. After cooling, the paraffin blocks included in the material are obtained.
To make a good inclusion, it is necessary that the fragment is completely dehydrated, clarified and properly impregnated.
This process can be performed more quickly with the use of a modular Embedding Center usually composed of three modules: warm, cold and central paraffin dispenser.

Robust equipment easy to handle, mounted in tubular frame plate in high resistance plastic resin finishing.

External finishing in white resistent to the lab environment and products as xylol.

Digital central panel with touch screen, with a microprocessor which controls all machine functions.

Calendar adjustments program: day, month, year, hour and minute.

Working temperature setting program: paraffin tank, left side tray, right side tray, draw-in tweezers stand, embedding table and paraffin dispenser nozzle.

Automatic operation setting program: daily programming for each day of the week, which allows two scheduling on the same day with hour and minute settings.
Integrated cooling spot (cold spot), facilitating the sample guidance in metal shapes.

Drive embedding by pedal or through the front plate under paraffin dispenser nozzle.

Heating spot to keep the shape heated during the embedding (hot spot).LED Illumination system of work surface.

A large-range magnifying glass assembled on flexible holder at the front part to help out in the embedding of small specimens.

Security: sound alarm that goes off when the temperature reaches 41 °f (5°c) if it is either higher or lower than the programmed temperature for any station.

Thermal protector for disarming high temperature to reach 100°c. General shutdown of the equipment. Automatic reset when the temperature drops 95°c.

It connects up to two peripherals programs. Two peripheral equipment such as a refrigerated plate and a heated plate which can work together with the center module enabling the drive daily programming to work.


Capacity: 120 plastic cassettes or 70 metallic shapes each bowl

Height: 11.61" (295 mm)
Width: 25.31" (643 mm)
Depth: 24.02" (610 mm)
Weight: 52.91 lbs (24 kg)
Power: 1000 watts
Voltage: 110 volts or 220 volts 50/60 hertz

Para ffin tank capacity: 4.5 liters

01 magnifying glass
01 pedal
01 strainer
01 instruction manual
01 warranty certificate

More Less

Product category: Microtomes

Cryostat CM2850

To allow analysis of tissue by light microscopy, they must be sectioned into thin and uniform slices. The optimum thickness may varies with the purpose of the study; it is recommended that the thickness from 4 to 6 mm in routine laboratories.
The instrument able to fabricate cuts with such precision is the microtome, consisting of three parts: body, block holder and object holder. It is considered also that some models have two handles, an adjustment crank and another cut.
Cryostat is used for making tissue sections that have been frozen. This equipment consists of a packaged rotary microtome inside a cold room with temperature below - 20 ° C.

Function and Characteristics:

It is designed under overall engineering and ergonomic concept. All the components are processed with computer numerical controlled machine

Specimen retraction function to proevent specimen from blade injury

With counter to calculate total thickness
Mandatory refrigeration structure be used compressor with pro-environment refrigerant R404

Adopt to UV and O3 sterilize for 30 minutes every time
Peltier for Specimen Clamp refrigeration may be on or off manually
Two defrost methods: automatic and manual

The high-precision unit is enclosed outside the cryostat chamber to protect it from thermal expansion and contraction , and keep minimum clearance and maintenance.

Artificial intelligence interface that easy to learn and operate.
LCD screen can display data such as thickness, thickness sum , controlling time, temperature, timed on/off and so on

Sleep Function. After activating this function, the temperature in cryostat chamber can be kept between - 1℃ an -10℃; when stop this function, the temperature in freeze chamber will arrive to working temperature within 30 minutes .

Control panel with locking function could to avoid wrong operation.

Handwheel locking function .
Wide freezing shelf may put 8 specimen cassettes .

Standard Delivery Include:

• 1 microtome

• 1 disposable Blade holder

• 1 Hexagonal Wrench

• 1 M5 Allen Key , 1 M3 Allen Key

• 1 box of Feather disposable blade

• 6 specimen clamp

• 1 power cord

• 2 fuse

• 1 operation manual

Technical Specifications

• Freeze chamber temperature rage: -35℃

• Freeze shelf minimum temperature:-45℃

• Lowest temperature of Peltier unit on freeze shelf :-55℃

• Lowest temperature of Peltier unit on Specimen Clamp : -50℃(working time of Peltier is 15 minutes.)

• Maximum specimen size 35*35mm

• Specimen vertical stroke:48mm ◎Specimen horizontal stroke:15mm

• Coarse feeding speed:300μm/s or 900μm/s ◎Section thickness range: 0 μm~100μm adjustable; 0μm~3μm, in 0.5μm increment; 3μm~10μm, in 1μm increments; 10μm~20μm, in 2μm increments; 20μm~100μm, in 5μm increments;

• Retraction range: 0-80um, in 5um increments

• Voltage and frequency:220VAC ±10%,50Hz/110VAC ±10% 60Hz

• Power:≤1000VA

• Weight:130kg

• Dimensions(W×D×H):805×715×1210mm

More Less

Product category: Microtomes

Tissue Processor PT09 TS

The principle of histological processing consists in diffusing reactants to the interior of the tissues and the removal of tissue fluid that, after fixation of the material itself is employed fixative.
The tissue processing also makes the hard fragments capable of providing sectioning thin and delicate slices for observation under the microscope.
Various substances can be used as a means of inclusion; However, in the conventional processing, commonly is used paraffin.
The processing material for inclusion in paraffin goes through three stages: dehydration, clarification and impregnation.
To realization and optimization of this process was invented Automatic Tissue Processor.

Robust equipment easy to handle, mounted in tubular frame plate in high resistance plastic resin finishing .

External finishing in white resistent to the lab environment and products as xylol.

Micro-processed central digital touch screen lcd panel, which controls all functions of equipment such as: date, time and year and equipment adjustment parameters configuration.

Daily schedule for 24 hours and slow time for weekends or extended holidays.

Changeable programming with selectable time interval according to the need of the operator. Ability to pause processing in any bath or position.

Adjustable bath speed and time control allowing total flow fully preventing contamination of one bath to other.
High duration battery own up to 10 years allowing data protection even in lack of power situations.

+/- 20 min continuos operation in lack of power situation. energy provided by nobreak variable according to nobreak capacity.

Protection sensor that controls paraffin mugs individually with visual and sonorous alarm protection for sub and super heating.

System protection not allowing the penetration of the last xylol paraffin bath, in case of not agreeable selected temperature parameter.

Automatic stop at end of cycle system. 9 storage protocols programs pre-selected by operator.

System oscillation inox basket with capacity up to 85 cassettes, wich improves the processed material quality.

Paraffin bath temperature control in panel, with adjustable sensitivity to 80 c +/- 1 c. capacity up to 255 plastic cassettes using 2 baskets.

Capacity to 10 quimical baths and 2 parafin baths, totaling 12 baths of 1000ml each.

Sealant bath lid that fully prevent environment contamination.


Capacity: 2 liter of reagent for bath

Height: 560 mm
Width: 800mm
Weight: 70kg
Power: 500 watts
Voltage: 110 volts or 220 volts 50/60 hertz

01 instruction manual
01 warranty certificate
03 stainless steel baskets with a
Capacity of 70 cassettes each
10 glass containers for chemical
Reagents and 01 as a back-up
02 paraffin mugs
01 nobreak
500 cassettes.


More Less

Product category: Microtomes

Linear Slide Stainer

Staining of tissues
The use of dyes is key to view the tissue under the light microscope. After the microtome, the cells and extracellular material are typically transparent and dyes enhance visualization of tissue structures.
The dyes applied to stain tissues that were previously set are called non vital stains, such as hematoxylin, eosin, fuchsin, among others.
We can also stain cells in culture or cell bodies are still alive; in this case, it is necessary to use dyes called vital that do not cause damage to cells and also does not interfere with cell metabolism. Among them are: the trypan blue, green Janus B, trypan red, methylene blue, neutral red, among others.
The automation of this process can be done with Slide Stainers.

The model tissue Processor is an apparatus used for
routine staining of animal, plant and human body
tissue. It can be widely used in such institutions as
hospitals, scientific research institutes, universities and
judicial departments for clinical pathologic analysis and
research on animal and plant cells.


● Self-adapted cover used with the multiple gasket seal produces excellent sealing performance, which minimizes the volatilization loss of the liquid.

● The organic glass housing, sealing strips and double layer active carbon filter ensure that the air in the room is not polluted.

The larger screen liquid crystal display enables the operator to see clearly the operation condition.

Manual operation can be used at will during running to adjust the staining efficiently.

Microtome sections are washed with circulating water to ensure clean sections without contamination.

The efficient large liquid tank can process as many as 96 microtome sections one time.

Technical Parameters

● quantity of Liquid tank: 19 

include loading capacity at a time: 96 pieces of slides

Capacity of Liquid tank: 800ml

quantity of circulating water tank: 2

retention time in each tank: 1 second~99

minutes and 59 seconds (can be set as need)

moving up and down: stirring every 15seconds

power supply: 220V±10% at 50Hz

power: 120W

outside dimensions(mm):1247×470×550

weight: 75 kg

Standard Delivery Include:

● 1 Stainer
● 2 Basket
● 1 Power cord
● 2 Fuse

● 1 1.5M Soft tube
● 1 Corner Valve
● 1 Three way pipe
● 4 connector

● 1 Pointed valve pipe
● 1 Teflon Tape
● 1 Operation Manual

More Less

About us

Company details

A Lupe Indústria Tecnológica de Equipamentos para Laboratório LTDA – ME (LUPETEC) was founded in November 2006 to supply the market with the manufacturer of equipment for Pathological high-tech laboratory and extreme reliability and to continue the work of the former Lupe Industry and Trade LTDA (Lupe).

Located in São Carlos, São Paulo State, known as Capital Technology has its own facilities and suitable for production and control of the equipment parts in a high quality standard.

LUPETEC is perceived by its customers as a company of extreme agility, differentiating the quality of its products and extreme efficiency of their outsourced service.

LUPETEC has accumulated extensive experience in the design, manufacture and application of products for pathological laboratories, which enables it to deliver high performance products for this segment.

It is continually invests in training its employees in updating and maintaining their equipment and search refinement within the most stringent quality standard and certified by ISO 9001 and ISO 13485 and C.E. mark.

Quality Policy
Through the improvement of our processes and products, develop and provide quality equipment that enables accurate and reliable diagnoses.

Our Vision
Develop and produce the best equipment for process diagnostics of Pathology.

Our Mission
Provide better quality of life through the development of equipment for cancer diagnosis.

Our Values


Keeping with stakeholder relations fair and acceptable


Have the obligation to answer for their actions


Have an obligation to make it right


Acquired over time in living with our customers and processes


Exercise our activities with integrity and honest

More Less