Metallux SA of Mendrisio at COMPAMED 2017 in Düsseldorf -- MEDICA Trade Fair
Manufacturers

Metallux SA

Via Moree 12, 6850 Mendrisio
Switzerland

Telephone +41 91 6406450
Fax +41 91 6406451
info@metallux.ch

Hall map

COMPAMED 2017 hall map (Hall 8a): stand K26

Fairground map

COMPAMED 2017 fairground map: Hall 8a

Our range of products

Product categories

  • 02  Electrical and electronic components
  • 02.27  Printed circuit boards

Printed circuit boards

  • 02  Electrical and electronic components
  • 02.32  Sensors, Micro sensors

Sensors, Micro sensors

  • 11  Manufacturing Services
  • 11.08  Bonding

Bonding

  • 11  Manufacturing Services
  • 11.12  Electronic systems / subassemblies

Electronic systems / subassemblies

  • 11  Manufacturing Services
  • 11.15  Extrusion
  • 11.15.10  Clean-room moulding

Clean-room moulding

  • 11  Manufacturing Services
  • 11.15  Extrusion
  • 11.15.12  Injection moulds

Injection moulds

  • 11  Manufacturing Services
  • 11.16  Forming
  • 11.16.13  Assembly

Assembly

  • 13  Services
  • 13.01  Design, Research and Development Services
  • 13.01.06  Electrical systems, subassemblies

Electrical systems, subassemblies

Our products

Product category: Pressure sensors

ME501 - Piezoresistive Flush Membrane

Metallux ME501/ME505 pressure sensors are made with a ceramic base cell and a flush diaphragm and work following the piezoresistive principle. The Wheatstone bridge is screen printed on one side of the flush ceramic diaphragm which is, in turn, glued to the sensor’s body. The bridge faces the inside where a cavity is made and the diaphragm’s opposite side can therefore be exposed directly to the medium to be measured. Because of the Al2O3 ceramic excellent chemical resistance (aggressive gases, most of solvents and acids, etc.), no additional protection is normally required. Metallux ME501/ME505 sensors are thermally compensated by laser adjustable PTC resistors and the use of ceramic ensures a high linearity across the entire range of measurement, reducing effects of hysteresis to a minimum.

More Less

Product category: Pressure sensors

ME662 - Piezoresistive Monolithic

Metallux ME662 monolithic pressure sensors are made with a ceramic cell and work following the piezoresistive principle. The Wheatstone bridge is screen printed directly on one side of the ceramic diaphragm by means of Thick Film technology. The diaphragm’s opposite side can be exposed directly to the medium to be measured. Because of the Al2O3 ceramic excellent chemical resistance (aggressive gases, most of solvents and acids, etc.), no additional protection is normally required. Thanks to the reinforced outer area (monolithic structure), the sensor can be mounted directly in a plastic or metallic case by using O-ring. ME662 sensors are designed in such a way so that temperature changes and pressure overloads do not cause loss in reliability. Use of ceramic ensures high linearity across the entire range of measurement and minimizes effects of hysteresis.

More Less

Product category: Pressure sensors

ME750 - Piezoresistive Monolithic with signal conditioning

Metallux ME75x and MEP75x are monolithic pressure sensors made with ceramic cell and work following the piezoresistive principle. The Wheatstone bridge is screen printed directly on one side of the ceramic diaphragm by means of Thick Film technology and signal conditioning electronics are added to generate 0.5…4.5 V ratiometric output (ME750), current loop 4…20 mA (ME751) or 0…10 V non ratiometric output (ME752). Also available in customized version I2C output. Pressure and temperature calibration are done electronically with the on-board ASIC and can be performed in bar (ME75x) or in psi (MEP75x). Electronics provide offset and span correction when temperature changes. Aging detection and compensation are constantly performed. This new method guarantees good precision and long-term stability. The Metallux ME75x family meets EMI requirements. The ASIC stores production lot specific data for sensor traceability and allows custom calibration. Due to the excellent chemical immunity of the the Al2O3 ceramic, the ME75x sensors are suitable for nearly all aggressive media.

More Less

About us

Company details

Founded in Switzerland in 1955, Metallux SA is a fast growing company internationally well known in the pressure sensor and microelectronics industry.
Since 2006, Metallux is part of the Eltek Group. This resource has permitted technological, engineering and manufacturing development with strong investments and a structural renewal.

BUSINESS BY INDUSTRIES

  • Industrial automation and control systems
  • Measuring devices and systems
  • Automotive
  • HVAC, Domotics & Safety
  • Water Management
  • Electromedical and Pharma
  • Military & Aerospace
  • Electronics

More Less