Alfamedic spol s.r.o. of Lisov at MEDICA 2017 in Düsseldorf -- MEDICA - World Forum for Medicine

Alfamedic spol s.r.o.

Tr. 5 kvetna 458, 373 72 Lisov
Telephone +420 387 994664
Fax +420 387 994603

Hall map

MEDICA 2017 hall map (Hall 11): stand H02

Fairground map

MEDICA 2017 fairground map: Hall 11

Our range of products

Product categories

  • 01  Electromedical equipment / Medical Technology
  • 01.09  Hospital and Care equipment
  • 01.09.05  Neonatal care equipment

Our products

Product category: Neonatal care equipment

Infant Warmer LN-91G

Applications: Standard care for new-born children including basic care in the labour room, body temperature stabilizing of hypothermical new-borns,

hyperbilirubinemia phototherapy treatment of new-borns, giving infusions and carrying out exanquinations, nursing pathological new-borns with controlled ventilation at the Intensive Care Units, Pre and Post surgery intensive care at infant and neonatological centers, executing surgery interventions at the Intensive Care Units and infant chirurgical centers.

The basic arrangement of all modifications contains:
  • Electronic proportional servoregulator, 2 temperature probes.
  • Mobile central stand with electric distributions.
  • Treatment bed with detachable plastic side-shields and adjusting to an uphold and drainage (Trendelenburgh) position (+/- 20°). Washable matress without heating.
  • Upper module with a heating body and built-in illuminatin and/or phototherapy according to the modification. The module is 90° revolvable.
  • Three hight-adjustable shelves placed above the treatment bed and one fixed shelf under the bed
  • Infusion glass or bag holder and a 2-liter oxygen bomb holder.
  • The basic arrangement is fully functioning and is ready for adding to the equipment.

Equipment choices:
  • Phototherapy with blue LED technology, irradiance level 50µW/cm2/nm, estimated life min. 30 000 hours
  • Matress with heating RD-95.
  • Central oxygen distribution with 2 outputs on the shelf under the treatment bed.
  • Time module - medical watch with the Apgar signalization.
  • Moulding fastening system - 2 mouldings.
  • Two drawers under the bed
  • Oxygen suction pump: a) without underpressure system b) with underpressure system.
  • Heated nebulizer OH-95.
  • Point hallogen reflector.
  • Oxygen flowmeter.
  • Oxygen microtent 500 mm (Polycarbonate).installation.
  • Treatment bed with measures: 65x80 cm
  • O2 cylinder holder
  • Heater IT-94 for infusion solution / or blood derivate tempering
  • Hight adjusting of treatment bed and heating module in the range of 40 cm - variant ECMO
  • Integrated X-Ray Tray under the bed
  • Neopuff™ Infant T-Piece Resuscitator
Technical data:
  • Power supply: 230V, 50 Hz
  • Display: LED
  • Temperature setting for auto mode: 33°-38°C
  • Temprature alarm: 39,0°C
  • Temperature display range: 20°- 45°C
  • Spot lighting: 20W / 12V
  • Area lighting: 50W / 12V
  • Max. power input: 1000 W
  • Dimension H x W x L: 1900 x 700 x 1050 mm
  • Heating power output: 600 W
  • Weight: cca 95 kg

More Less

Product category: Neonatal care equipment

Phototherapeutic lamp FL-2010

FL-2010 is the next generation of high intensive phototherapy, it is designed using advanced LED technology. Compact LED modules are used as the irradiance sources. They are equipped with special optics, which increase the intensity of irradiance, providing estimated life up to 30,000 hours without replacement of the LED modules. The irradiance does not affect the temperature of the patient.

The device is controlled by a microprocessor and touch screen LCD display. For maximum patient safety the device is supplied with a monitor of the patient temperature. When the temperature exceeds the threshold of 38,5 °C, the acoustic signal is switched on. In 1 minute, if the problem with high temperature is not solved by staff, the device turns off automatically. 
The device is also equipped with a timer, which gives the possiblity to set the duration of therapy. After the specified period, the device turns off automatically and informs staff with the acoustic signal. Lamp can working in two modes: continuous and intermitent mode. White light mode allows observation of patient skin colour.

Built-in counter of worked hours informs staff about the upcoming service control of the device.
The lamp is available in one versions: as a mobile stand with the vertically and horizontally adjustable lighting head.

More Less

Product category: Neonatal care equipment

Heated Mattress RD-95

Heated mattress is an optional local heat source for treatment of hypothermic states of patients. The unified design of the device enables its application almost in all fields of health service, intensive and reanimation care units, surgical departments, operating rooms, resuscitation departments, gynaecology, internal medicine departments, birth, children's and neonatal departments.

The main functional parts are electronic temperature regulator and patient's mattress. The regulator maintains the temperature according to required parameters and provides a constant diagnosis of the circuits. The heated mattress with a built-in heating system, a set of temperature sensors and a thermal mechanical fuse is connected to the regulator through plastic connector with a safety nut. Low supply voltage of the mattress of 9V / 18V depending on the size provides the high operating safety. The required operating temperature is set-up with the keys on control panel. The set-up data are represented by the red LED display. Excess of the set-up temperature and a possible regulation failures are signalled by optical and acoustic alarms. This always results in automatic disconnection of heating. Therefore the uncontrolled increase of temperature and the patient injury is prevented.

Green indicating light of heating currently signalises the instantaneous operating state of the device

More Less

Product category: Neonatal care equipment

Newborn bed MINI

Neonatal bed MINI is designed for neonatal and children's departments of all health facilities. It is in particular suitable for ROOMING – IN system as its design enables to put it directly above the mother's bed or under a heating module VM–94 or photo-therapy FL-2010.

It is mobile and can be easily adjusted manually in vertical direction. Four side swivel wheels, two with brakes. On the lower part of chassis there is a storage basket.

Through an easy positioning mechanism you can adjust the bed surface to both of „Trendelenburg's“ positions, a high-level or so-called „drainage position“. Lining of the mattress can be chosen between the cloth, leathercloth or purplast MINT. The bed can be used with a heated mattress with the temperature regulation type RD – 95.

More Less

Product category: Neonatal care equipment

HICO-Ultrasonat 810

The compact unit of the HICO-ULTRASONAT 810 meets the high requirements of a diversely qualified device with a design and operation which is quite accessible for those not familiar with the technology. A pleasant alternative for patients in local anesthesia.

The HICO-ULTRASONAT 810 works with a max. frequency of 1.7 MHz and a HF output capacity of approx. 32 W. The electrical energy is converted to mechanical energy through the piezo-ceramic transducer. The resulting vibrations reduce the liquid to the smallest particles of 0.5 to 6 µm in the nebulizing chamber. The transducer requires approx. 15 sec. after the unit starts for automatic calibration.


By automatic calibration of the transducer and a largevolume nebulizing chamber it is possible to nebulize over 500 ml liquid in succession without additional containers. This corresponds to 3-4 hours nebulization without refilling system or up to 8 hours with reduced intensity. An electronic dry run protection device replaces a float switch subject to failure.
An optimal hose guide makes it possible to guide the ventilation hose under the housing. Only the aerosol hose on the device is visible. The nebulizing chamber is surrounded by a gutter for the drainage of dripping water. A coarce air and a bacteria filter (with CE mark) ensure germ-free mist to guaranty the highest possible hygiene safety.
The aerosol liquid can also be heated with a heating system built into the aerosol hose (as accessory). A heater wire covered with a plastic insulation is embedded into the aerosol hose. The heater only functions when the hose connector has been plugged into the corresponding standard jack on the device and only when the machine is nebulizing, i.e. in function.

More Less

About us

Company details

The company Alfamedic was founded in August 1990. It was established as a new independent Czech business entity, without foreign participation and without previous ties to other companies. The main sphere of business of the company is development, manufacturing and sale of high-quality medical devices and equipment.

The company activities focus on the following fields of medicine: neonatology, paediatry, gynaecology, surgery, orthopaedics and rehabilitation.
Products manufactured by Alfamedic form comprehensive conceptual series. With the gradual expansion of its range of products the company also increases opportunities for their application in other fields of medical care.
The key product of the production program is a “heated bed for newborns “ (open incubator) which is available in a number of modifications and can be equipped with a high number of accessories, e.g. heated mattress, resuscitator, phototherapy, infusion heater, heated nebulizer, etc.
In 2010 Alfamedic introduced on the market a completely new device for treatment of neonatal jaundice - a phototherapeutic lamp FL-2010 equipped with modern high power LED technology, with long service life and the possibility of patient monitoring.
In the surgery field the company offers for example heated trays with accurate regulation of temperature. The range of products also includes a number of heated water baths (from 5 to 50 litters) suitable also for other fields of medicine and laboratories.
The products find use in the health sector of the Czech and foreign markets. The quality of products has been proved by many years of cooperation with numerous partners abroad. The current share of export is ca. 65% of the total production.
The main objective of the company is to offer to customers an adequately priced high quality range of products that will be able to meet demanding requirements and successfully compete even on foreign markets.

More Less